$ 129.99 $ 185.70
The ’74 Vintage Phase 90 is a faithful reissue of the original, featuring hand-matched FETs and a hand-wired circuit board.
This pedal can only be powered by one 9-volt battery (not included).
$ 189.99 $ 271.41
The EVH Flanger features an Unchained switch for instant EVH tone and comes fittingly adorned with Eddie's famous striped graphics.
This pedal can be powered by two 9-volt batteries, a 18-volt adapter or the DC Brick™, Iso-Brick™ and Mini Iso-Brick™ power supplies.
Sold Out $ 214.27
The MXR Ten Band EQ lets you tune your bass or guitar rig in seconds, and it’s been upgraded with noise-reduction circuitry, true bypass switching, a lightweight aluminum housing, brighter LEDs, and a second output.
This pedal can be powered by the included ECB004 18-volt adapter or the DC Brick™, Iso-Brick™ and Mini Iso-Brick™ power supplies.
$ 99.99 $ 128.56
The MXR M-132 M-132 Super Comp Compressor Pedal is an improved version of the legendary Dyna Comp. This is the guitar effects pedal that's the ultimate source for the "Nashville sound." Attack level control preserves initial volume without sacrificing sweet sustain. Sensitivity control lets you dial in just the right amount of compression. The Super Comp effects pedal has a super-tough housing with bypass footswitch and LED.
$ 169.99 $ 242.84
The gorgeous-sounding MXR M-134 Stereo Chorus Pedal will remind you how cool chorus can be. Want to add sparkle to clean-toned arpeggios? Animate strummed passages? Widen and fatten distorted power chords? This box will do it all, cleanly and quietly. Set the Rate and Width controls to your liking and then dial in as much effect as you want with the Intensity knob. You can then shape the tone even further by EQ-ing the modulated frequencies with the bass and treble controls. Run in mono or use the stereo outputs for a huge, vibrant sound. If you're looking to preserve the low end of your guitar tone, the MXR Stereo Chorus has got you covered with its Bass Filter button that applies the effect to the high frequencies only.
Sold Out $ 185.99
The MXR M-135 Smart Gate Pedal gives you 3 selectable types of noise reduction: Hiss, Mid, and Full. Bites down on hiss and hum but lets all of your music shine through. Intelligent design provides dual high and low adaptive filters, opens at lightning speed, introduces no extra distortion, and lets you control the sensitivity of the gate's threshold. The MXR M-135 Smart Gate Pedal features hardwire bypass with footswitch and slim, tough stompbox housing.
$ 149.99 $ 214.27
This power supply is light and pedalboard-friendly with ten fully isolated outputs ranging from 9V to 18V—including two variable 6V–15V outputs—and special noise-reduction circuitry for quiet operation.
This pedal can be powered by the included ECB009 18-volt adapter.
The Iso-Brick Power Supply is small and light with tons of quiet, noise-free DC power on tap ready to run a wide range of pedal types without crowding or weighing down your pedalboard.
Each of the Iso-Brick Power Supply's 10 outputs is fully isolated, eliminating gig-ending ground loop noise. Whether analog or digital, positive or negative ground, this power box has you covered. The MXR team broke down these 10 outputs to accommodate a variety of voltage and current requirements: two 9V outputs at 100mA, two 9V outputs at 300mA, two 9V outputs at 450mA, two 18V outputs at 250mA, and two variable outputs adjustable from 6V to 15V at 250mA. The two variable outputs can be used to emulate voltage "sag", drained battery effect sought by many vintage tonechasers.
On top of all that, the Iso-Brick Power Supply comes in a small, lightweight housing that's built like a tank. Features power on/off and connection status LEDs. Put this little box on your pedalboard to make sure it runs reliably and quietly gig after gig.
$ 169.99 $ 242.84
$ 99.99 $ 142.85
When you want to be heard, get the Booster Mini! The MXR Booster Mini gives you the sonic secret sauce of the Echoplex Preamp with the legendary boosting power of the MXR Micro Amp in a lightweight, space-saving mini housing. The Volume control has up to +25dB on tap while the Tone control rolls off highs. To add a little extra grit to your signal, adjust the internal Echoplex Preamp level control. Put the MXR Booster Mini on your board to save space, season up your tone, and fly high above the mix.
MXR Booster Mini Pedal Features
$ 169.99 $ 242.99
The MXR Bass Preamp combines a pristine bass preamp with a studio-quality Direct Out in a Phase 90-sized box, providing clear tone without hogging precious pedal board space. Use it to add a new voice to an old passive bass, sweeten up any amp, or put some special sauce on a particular song. Dial it in just the way you want it and send it straight to the house-pre or post-EQ-with the built-in Direct Out.
The Bass Preamp features separate INPUT and OUTPUT level controls and a 3-band EQ section with sweepable midrange-from 250hz to 1khz-for extensive tonal flexibility. It's all delivered super clean with high headroom thanks to our own Constant Headroom Technology, and you can use the PRE/POST EQ switch to set whether or not your Direct Out signal is affected by the Bass Preamp's EQ section. And of course, the Bass Preamp features a GROUND LIFT switch in case you encounter ground loop hum.
The Bass Preamp is factory preset to operate in ¼" out buffered bypass and Direct Out active. For players who only want to use the ¼" out, there are two internal switches that disable the Direct Out and ¼" out buffered bypass for true ¼" out bypass mode.
Sold Out $ 142.84
The Boost/Line Driver provides up to +20dB of ultra-clean boost to rejuvenate the sparkle, punch, and brilliance of your sound.
This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included).
The Boost/Line Driver is simple in design but superbly effective in solving a variety of mismatched line level and signal conditioning problems that can occur when combining effects. The MC401's circuit design has been used for years by CAE in the world's best guitarist's rigs to remedy these problems and rejuvenate the sparkle, punch and brilliance that can be lost. It can also be used as an ultra-clean boost (up to +20dB) for solos or to drive effects for more dynamics and sensitivity.
$ 129.99 $ 185.70
This pedal provides a huge, responsive range of gritty and textured tones that enhance the sound of your rig while preserving its fundamental character—and in an MXR mini housing, this pedal will free up some serious pedalboard space.
This pedal can be powered by a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included).
The MXR Timmy Overdrive provides a huge range of gritty, textured tones that enhance your rig’s sound while preserving its fundamental voice—and in an MXR mini housing, it’ll free up serious pedalboard space. The pedal’s based on a design from veteran pedal builder Paul Cochrane that’s widely celebrated among high level pros, from first-call Nashville player Kenny Greenberg to first-call L.A. player Lyle Workman to rockstar Brad Whitford. When Paul decided to bring his pedal to a wider audience, he chose to work with the MXR design team. “It’s an honor to work with MXR,” Paul says. “My first ever pedal was a Phase 90.”
Thanks to Paul’s inventive implementation of clipping options and tone controls, the Timmy Overdrive is a dream come true for working guitar players. The Clip switch provides three different clipping styles for a multitude of scenarios, whether you need a big, bold always-on sound with a ton of headroom to slam the front end of your amp, a more compressed and saturated sound for fat chords, or anything in between. The Bass and Treble controls offer further refinement in two key ways. First, they’re cut-only, keeping your signal’s character intact while making it super easy to dial in a clean boost. Second, Paul wired the Bass control to affect your pre-OD signal so that you can your maintain low end at lower Gain settings and the Treble control to affect your post-OD signal so that you can adjust the top end to keep dirty settings smooth and musical.
Finally, the MXR design team worked with Paul to select an op-amp that perfectly complements his expertly crafted design. They chose the LF353, a component well-respected by Dunlop engineers for providing high output, high gain, and hi-fi signal delivery. The resulting MXR Timmy Overdrive is a professional-grade must-have for players who want sweet, harmonic breakup that responds to playing dynamics and maintains a rig’s personality at a fraction of the standard pedal size.