Products
Tech 21 SansAmp Bass Driver V2 DI Effects Pedal
$ 249.00 $ 335.00
Much more than just a direct box, the SansAmp Bass Driver DI is capable of dialing up big vintage tube tones, bright modern slap sounds, gnarly distortions, and all in between. Three different outputs to drive power amps, recording desks, PA mixers, or simply enhance your current rig. Controls include Presence for definition and upper harmonic content; Blend to combine the proportion of direct signal and SansAmp circuitry; and active EQ specifically tuned for bass with 12dB of cut or boost.
VERSION 2
With the popularity of 5- and 6-string basses going beyond fad status and becoming mainstream, we added a switch to adjust the bass frequency to extend into those lower registers. We also added a mid-range control and a switch to adjust its frequency. The core of the SansAmp Bass Driver and all of its tones remain true to its original design.
- Preamp, stompbox, and direct box in one
- Offers a wide range of bass amp sounds
- Active EQ boosts/cuts up to ±12db
-
BUILT-IN SPEAKER/CAB SIM: The 100% analog SansAmp Tube Amplifier Emulation technology encompasses the entire signal chain, from pre-amp to power amp to speaker simulation. An integral part of the circuitry, the SansAmp speaker simulation will complement any type of guitar or bass speaker cabinet system. You can also place an external IR after a SansAmp to give additional flavor if you so desire. The SansAmp speaker sim is designed and individually tailored for a smooth, even response as would be achieved by a multiply-miked cabinet –without peaks, valleys, and notches associated with single miking and many IRs.
For studio and live applications, SansAmp Bass Driver DI is engineered with three outputs:
• effected XLR
• effected 1/4″
• parallel, uneffected 1/4″The footswitch activates the Tube Amplifier Emulation circuitry. Disengaging the circuitry enables you to use SansAmp Bass Driver DI as a standard active transparent direct box.
Measures 4.75″ x 3.75″ x 2″
• Operable via phantom power.
• Operable with 9V alkaline battery (not included).
Tech 21 SansAmp Para Driver V2 DI Pedal
$ 249.00 $ 335.00
This floor version of our RPM rackmount provides the same detailed tone shaping possibilities for any signal source. It is particularly useful with acoustic, electric and bass guitars, and upright bass, either direct to a mixing console or with an instrument amplifier. The Para Driver DI gives your instrument a natural warmth and presence, as if miking it through a tube pre-amp. The SansAmp circuitry eliminates the harsh, unnatural harmonics of piezo pickups, while the Drive control offers some tasteful edge — just a little or over-the-top.
Version 2 has exactly the same tonality and functionality with the addition of two new features: Rumble Filter and Air. The Rumble Filter removes unwanted sub-sonic frequencies that cause boominess and audible handling noises associated with acoustic guitars.The Air button adds top-end clarity and sparkle to acoustics.
PARA DRIVER DI
FEATURES
| Active tone controls with 12dB of cut or boost | |
| Sweepable semi-parametric EQ | |
| 1/4-inch 4.7 megOhm instrument level input | |
| 1/4-inch and XLR outputs with selectable levels | |
|
Parallel, uneffected output to run a dry signal to a separate channel |
Tech 21 SansAmp Programmable Bass Driver PBDR
$ 249.00 $ 398.00
Always thinking of our fat-stringed brethren, we had to make a 3-channel, programmable, rig-in-a-box for bassists who can’t get enough of a great thing. Like the TRI-A.C. for guitar, you get three hot tones right at your toetips. The all-analog circuitry features the same controls as its single channel predecessor: Drive, Bass, Treble, Presence, Blend and Level. Digital only in its programmability, you just tweak the knobs until you find a tone, double-tap on a footswitch, and it’s saved in that channel. It’s that simple. Three of your faves — to go!
- Build your Bass Driver DI into a live rig with a Bass Power Engine 60, and run through the PA for extra power.
- Boldly go live with just your Bass Driver DI straight into the PA.
- Bounce into any studio with a Programmable Bass Driver DI and plug directly into the board.
- BUILT-IN SPEAKER/CAB SIM: The 100% analog SansAmp Tube Amplifier Emulation technology encompasses the entire signal chain, from pre-amp to power amp to speaker simulation. An integral part of the circuitry, the SansAmp speaker simulation will complement any type of guitar or bass speaker cabinet system. You can also place an external IR after a SansAmp to give additional flavor if you so desire. The SansAmp speaker sim is designed and individually tailored for a smooth, even response as would be achieved by a multiply-miked cabinet –without peaks, valleys, and notches associated with single miking and many IRs.
- While larger than our other SansAmp pedals, the Programmable Bass Driver DI still fits into a gig bag. Actual size: 7.25”L x 5.25”W x 2.25”H.
- Even with its roadworthy all-metal construction, each unit weighs in at a mere 25 oz.
- Operable via phantom power.
- Operable with 9V alkaline battery (not included).
- Optional DC power supply is available:
Info
Shop
News & Updates
Sign up to get the latest on sales, new releases and more …
© 2025 Huber Breese Music. Powered by Shopify
