Products
A-Tempo CJ-CONGA-SM Cajon Conga
Sold Out $ 225.00
New from A tempo (formerly Sol Percussion) we have the amazing new Cajon Congas. These instruments play like congas but are build like cajons. The effect is that of a hybrid between the two instruments, offering you the ability to play traditional conga patterns and have the woody effect of a cajon. Open tones are resonant and clear and the slap sounds cut more so than a traditional conga. These are the new "fun go to" instruments by the staff of Explorers. Enjoy them today!
Acoustic 1973 450 Solid State Bass Amplifier and 404 Bass Cabinet USED
Sold Out
Used amplifier and cabinet. Sold as pair. Comes with original owners manual and cover(s). Recently serviced by an amp tech.
LOCAL SALE ONLY / WILL NOT SHIP
MODEL 450 ELECTRICAL SPECIFICATIONS
1. OUTPUT
- Power output (continuous) across 4 ohm load @ less than 5% distortion: 170 Watts RMS
- Peak power output (instantaneous) across 4 ohm load @5% distortion: 450 Watts
- Power output (continuous) across 2 ohm load @ 5% distortion: 170 Watts RMS
- Peak power output (instantaneous) across 2 ohm load @ 5% distortion: 400 Watts
- Preamp gain (from input to line output): 38 dB or 80X
- Total gain: 63.5 dB or 1500X
- Power amplifier gain from ext. inputs speaker output: 55 dB or 500X
- Input voltage for maximum output: Input 1: 15mv RMS / Input 2: 45 mv RMS
- Input voltage capability (maximum): Input 1: 15 mv RMS / Input 2: 1.6V RMS
- Nominal Input impedance: Input 1: 470K OHMS / Input 2: 69K OHMS
- Noise-to-full-output ratio
- -volume minimum: 78 dB below full output
- volume maximum: 78 dB below full output
5. FREQUENCY RESPONSE
- At 10 Watt level: -3dB, 27 Hz to 21K Hz
- Power bandwidth 1/2 power point
6. AUXILIARY OUTPUTS
- Output Voltage: 250 mv RMS
- Impedance: 5000 ohms
- Booster Output: 275 mv RMS
- Impedance: 1 K ohms
- Minimum Input Required to Clip Power Amp: 425 Microvolts
8. RANGE OF TONE CONTROLS
- Bass: +15 dB Boost, -15 dB cut @ 50 Hz
- Treble: +15 dB Boost, -25 dB cut @ 10KHz
- Mid-Range: +7 dB Boost, -30 dB cut @ 400 Hz
- Bright Switch Boost: 6 dB per octave from 200 Hz to 5KHz
9. RANGE OF GRAPHIC EQUALIZER
- Section 1: +/- 16 dB @ 70 Hz
-
Section 2: +/- 16 dB @ 140 Hz
-
Section 3: +/- 16 dB @ 280 Hz
-
Section 4: +/- 16 dB @ 1100 Hz
-
Section 5: +/- 16 dB @ 2200 Hz
MODEL 404 SPEAKER CABINET SPECIFICATIONS
- Speaker Complement: 6 Eminence 12" Speakers
- Cabinet Design: Sealed System
- Cabinet Construction: 3/4" Braced Plywood
- Speaker Access: Snap-Off Grill Frame
- Speaker Mounting (each speaker): .8 Bolts (8-32 Threads)
- Cabinet Size: ...42" H × 28" W x 15" D
- Shipping Weight: 137 Ibs.
- Nominal Impedance: 4 ohms
- Power Handling Capacity: 200 Watts Continuous
Action Custom Straps Big Top Parrothead Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
Action Custom Straps has been designing and making Jimmy Buffett's guitar straps for over 14 years now. Big Top was added in 2010. Big Top is made by hand in Indianapolis, IN, one at a time using soft white top grain leather. Big Top features an embroidered body that is folded and seamed precisely down the underside of the strap. This construction eliminates any edges. Big Top is 2 1/2" wide and the standard length adjusts from 44" to 54".
Action Custom Straps has always preferred not to cut holes in the body of their straps (which is too soft to be used in this way), so instead an additional back adjustment piece is added that gives a clean look no matter where the strap is adjusted. Soft leather is used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a single stitch.
**Guitar pictured is not included.
Action Custom Straps Headstock Strap - Black Top Grain Leather
Sold Out
Sure, you can tie your new strap on your expensive guitar with an old shoe lace. But why do that? Why not simply mention that you need an ACTION headstock strap sent when your custom guitar strap is shipped. No problem, no charge. Your strap will be happier and your guitar will thank you.
Action Custom Strap's black top grain leather headstock adds a touch of class to any guitar strap that attaches to the headstock. Two leather stars add some style and thickness while a decorative Chicago screw holds it all together. Sure, a shoestring will work, but their black headstock strap adds a custom touch that a shoestring just can't offer!
Action Custom Straps Headstock Strap - Brown Top Grain Leather
$ 10.00
Sure, you can tie your new strap on your expensive guitar with an old shoe lace. But why do that? Why not simply mention that you need an ACTION headstock strap sent when your custom guitar strap is shipped. No problem, no charge. Your strap will be happier and your guitar will thank you.
Action Custom Strap's brown top grain leather headstock adds a touch of class to any guitar strap that attaches to the headstock. Two leather stars add some style and thickness while a decorative Chicago screw holds it all together. Sure, a shoestring will work, but their brown headstock strap adds a custom touch that a shoestring just can't offer!
Action Custom Straps Huber Breese Legacy Vachetta Guitar Strap
$ 229.99
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Huber Breese Legacy custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way! The strap has our Huber Breese logo featuring the guitar and drum cartoon of Paul Huber and Terry Breese along with the"HB" initials!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**Guitar pictured is not included.
Action Custom Straps Limited Edition Echo Flame Red and Black Custom Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Limited Edition Echo Flame custom guitar strap is made using a very soft top grain cowhide leather for the hand rolled body. Hand rolling the body means that the sides are rounded, thus eliminating any edges that might even slightly cut into your neck with extended wear.
The Moore & Giles Echo Flame red leather inlay adds a distinct and bright contrast in materials!
Action Custom Straps has always preferred not to cut holes in the body of their guitar straps (which is too soft to be used in this way), so instead, they add an additional hidden adjustment piece that gives a clean and custom look no matter where the strap is adjusted. Soft leather is used where it can be appreciated and stronger leather where it is needed! After the strap is assembled with 9 carefully cut pieces of leather, the body is sewn with a double stitch.
The Limited Edition Echo Flame is 2 1/2" wide and will adjust from 44" to 61" and comes with a second (shorter) tailpiece.
**Guitar pictured is not included.
Action Custom Straps Simply Classy Black Distressed Limited Edition Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Black Distressed Limited Edition custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**This guitar strap is semi-naked leather and will bleed if wet. (So if you sweat a-lot while playing, you might want to choose another strap!)
**Guitar pictured is not included.
Action Custom Straps Simply Classy Black Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Black 100 custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**Guitar pictured is not included.
Action Custom Straps Simply Classy Black with Single Silver Stitching Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Black with Single Silver Stitching 100 custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**Guitar pictured is not included.
Action Custom Straps Simply Classy Brown Distressed Limited Edition Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Brown Distressed Limited Edition custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**This guitar strap is semi-naked leather and will bleed if wet. (So if you sweat a-lot while playing, you might want to choose another strap!)
**Guitar pictured is not included.
Action Custom Straps Simply Classy Dark Red with Gray Python Ends Guitar Strap
$ 175.00
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy Black 100 custom guitar strap is made using a very soft top grain leather one piece body. The ends are made of real Gray Python (his name was Bob!) The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**Guitar pictured is not included.
Action Custom Straps Simply Classy White Guitar Strap
Sold Out
Huber Breese is proud to team up with Terry Misner and the Action Custom Straps brand of Indianapolis, IN to carry a small run of straps in our store! Action Custom Straps not only makes some of the finest hand made straps on the market, but also makes straps for some of the biggest names in the music industry! Artists such as Jimmy Buffet, Mac McAnally, Keith Urban, Billy Corgan, Elvis Costello, Miranda Lambert, Eric Church, Trace Adkins, Gary Clark Jr., Travis Tritt, and many more!
The Simply Classy White 100 custom guitar strap is made using a very soft top grain leather one piece body. The body is carefully and precisely folded and seamed down the middle of the underside. This construction means that the sides are rounded, thereby eliminating any edges that might even slightly irritate your neck with extended wear. And it goes without saying that the leather has to be soft in order for the body to be made this way!
Action Custom Straps never cuts holes in the body of their straps (which is too soft to be used in this way), instead an additional hidden adjustment piece is added that gives a clean and custom look no matter where the strap is adjusted. This allows soft leather to be used where it can be appreciated and stronger leather where it is needed! After the strap is assembled, it is sewn with a strong matching double stitch.
This strap is a Series 100 meaning it is 2 1/2" wide and will adjust from 44" to 54".
**Guitar pictured is not included.
ADJ Fog Fury Jett Pro Fog Machine DEMO
Sold Out
Demo model. May have been used a couple times for demonstration.
The ADJ Fog Fury Jett Pro is a high velocity vertical Fog Machine that mixes color into the fog from 28x 3-Watt LEDs (6 Red, 7 Green, 6 Blue, 3 Amber & 6 UV LEDs). The Fog Fury Jett Pro produces a dry even blast of fog over 40 feet (12 meters) in the air. It has a special heating element design that uses an oil type transmission throughout the pipeline to prevent clogging. It is also equipped with a high performance Italian pump system for optimum output. ADJ’s Electronic Thermo Sensing (ETS) technology is on-board to maintain optimum heat levels with short warm-up time between fog blasts.
The Fog Fury Jett Pro may be use vertically or horizontally. The reservoir tank may be mounted in the front or rear of the unit so the machine may be pointed up or down. Control options included 3-pin and 5-pin DMX In/Out connections, ADJ’s WiFLY EXR wireless DMX on-board, plus the ADJ FFJWR wireless remote comes included in the box.
For a CO2 style effect, use ADJ's F4L QD, quick dissipating fog fluid.
Specifications
Features:
• LED and vertical fog effect combination
• Operates in multiple positions
• On Board control or remote control
• WiFLY EXR Wireless DMX (up to 2,500 ft. /760M line of sight)
• ADJ’s Electronic Thermo Sensing (ETS) technology
• Safety cable eye bolt
Technical Information:
Optical: 28 x 3-Watt LEDs (6 Red, 7 Green, 6 Blue, 3 Amber & 6 UV LEDs)
Output:
• Output: 40,000 Cubic Feet Per minute
• Heater: 1450 Watts
• Consumption: 1550 Watts
• Heat Up Time: 9 min
• Reheating time between intervals: 80 Seconds
• Fluid Type: Water Based Fog Fluid
• Fluid Consumption: 150ml/min
• On board control or Wireless DMX
Connections:
• Data: 3-pin & 5-pin DMX In/Out
Control:• DMX Channels: 1, 2, 3, 7, & 9
• WiFLY EXR Wireless DMX (2,500 feet line of sight)
• Remote Control Included: FFJWR
• On Board Control: Yes
Electrical:
• AC 120V/60Hz or 240/50Hz (non switching)
Physical:
• Dimensions (LxWxH): 16.5” x 12.5” x 8” / 419 x 315 x 206mm
• Weight: 21lbs. / 9.5 kg
• Tank Size: 2.5 Liter removable tank
What’s Included:
• Manual
• ADJ FFJWR - wireless remote
Certifications:
• ETL Approved
AKG D12VR Reference Kick Drum Microphone
$ 603.00 $ 755.09
The D12 VR is a large-diaphragm cardioid dynamic microphone. Designed specifically for kick-drum recording applications, the microphone has a thin diaphragm to enhance the low frequency performance. Its predecessors have been the industry standard in kick drum mics for decades. The D12 and subsequently the D12E and the D112 have been the choice of drummers and the live sound engineers who love them since 1950.
Without phantom power, the microphone delivers the pure character of the sound source. With phantom power enabled, one of three switchable active-filter presets can be used to quickly adapt the microphone response to suit the desired kick-drum sound. The filter setting can be controlled using a switch on the microphone body. In this mode the output level is also reduced by 10 dB automatically.
Check it out. The latest version of a classic. It has retained the attributes of the original but taken advantage of modern innovations. Vintage and modern have just met up, and they have done so in front of the kick drum head.
D12VR Large-Diaphragm Cardioid Dynamic Kick Drum Mic
- Type: dynamic pressure gradient transducer
- Polar pattern: cardioid
- Frequency range: 17 - 17000 Hz (±2 dB)
- Sensitivity: 1,2 mV/Pa ± -58 dBV (at 1000 Hz passive)
- Max. SPL: 164 dB SPL (for 0,5 % THD)
- Impedance: <200 ohms (at 1000 Hz)
- Recommended load impedance: >1000 ohms
- Environment temperature range: -10 C - +70 C
- relative humidity at +20 C: 90 %
- Connector: three-pin male standard XLR
- Finish front grille: glossy galvanized nickel matte,
- rear grille: matte black paint
- Dimensions: 125 mm x 101 mm x 66 mm (4.9" x 3.9" x 2.6")
- Net weight: 500 g (1.1 lbs)
AKG D40 Professional Dynamic Instrument Microphone
$ 119.00 $ 154.86
SOUND IN MOTION
for drums, percussion, wind instruments and guitar amps on stage
The D40 professional instrumental microphone with its solid all-metal body will stand up to the hardships of night-after-night onstage use with a smile. Its patented Varimotion diaphragm uses a unique laminated material to damp high resonance peaks, leading to a quantum leap in audio performance. The transducer is protected by a sturdy wire-mesh cap and can take extremely high sound pressure levels with ease.
An integrated stand adapter in combination with the included H440 mounting bracket makes the D40 a highly versatile tool for use on drums, percussion, wind instruments and guitar amps.
TECHNICAL SPECIFICATION
General
- Audio Frequency bandwidth: 75 to 17000 Hz
- Sensitivity: 2.2 mV/Pa
- Electrical Impedance: 200 Ohms
- Recommended Load Impedance: 2000 Ohms
- Polar Pattern: cardioid
Audio Output
- Type: Balanced XLR
- Gender: Male
- Contacts: 3-pin
Design
- Body: Metal
- Finish: dark stage blue
Dimensions / Weight
- Length: 104 mm
- Height: 79 mm
- Diameter: 44 mm
- Net Weight: 245 g
AKG K141 MKII Semi-Open Studio Headphones
$ 149.99 $ 189.99
The K141 MKII headphones feature gimbal suspended leatherette and velvet ear cups and a self-adjusting headband for great fit and maximum comfort, even in long work sessions. A professional mini XLR connector allows quick replacement of the cable.
On-ear, semi-open design
for solid base and airy highs
Optimized for single-ear use
keeps the familiar sound and makes intonation easier
Patented Varimotion 30mm XXL transducer
for accurate signal transfer and great dynamic range
Leatherette and velvet ear pads
for maximum wearing comfort
Self-adjusting headband
for optimum fit and ease of use
AKG K240 Studio Semi-Open Professional Headphones
Sold Out $ 154.86
The AKG K240 Studio over-ear, semi-open headphones are designed for professional applications such as mixing, mastering and playback. Their advanced 30 mm XXL transducers with patented Varimotion diaphragms deliver a wide dynamic range, increased sensitivity and high sound levels, while their semi-open design provides a solid bass range and extremely clear highs. With impressive accuracy, musicians, producers and engineers rely on the AKG K240 Studio to clearly hear mixing details, which has made these headphones a standard in recording settings. In addition to great sound quality, the headphones are extremely durable and comfortable. Not only built to withstand the demands of countless hours in the studio, their self-adjusting headband provides an ideal fit and their over-ear pads nicely envelop the ears. The AKG K240 Studio headphones also feature a professional mini XLR connector and come with a 3 meter cable and convertible jack plug for connecting portable equipment easily. Altogether, from performance and ease of use to comfort and reliability, the AKG K240 Studio is a powerful tool for production environments.
Features
- 55-ohm impedance
- Removable, serviceable cable
- Varimotion technology for enhanced bass
- Type: semi-open, circumaural
- Frequency range: 15Hz-25kHz
- Impedance: 55 ohm
- Sensitivity: 91dB/mW
- Power handling: 200mW
- THD: <0.25%
- Connector: gold-plated, 1/8" stereo mini jack and 1/8"-1/4" adapter
- Net Weight: 8-1/2 oz.
General Specifications
- Driver size (mm): 30
- Sensitivity (dB SPL/V @ 1 kHz): 104
- Rated impedance (Ω: )55
- Audio frequency bandwidth (Hz): 15 - 25000
- Maximum input power (mW): 200
- Cable(s) length (m): 3
Audio Interface
- Type: Stereo plug – 3.5mm (1/8-inch) with 6.3 mm (1/4”) screw-on adapter
- Gender: Male
- Contacts: 3-pin
Application
- Studio Mixing: Yes
- Hi-Fi Listening: Yes
Features
- Foldable: No
- Replaceable Earpads: Yes
- Semi-open: Yes
- Over-ear: Yes
- Detachable cable: Yes
Audio Specifications
- Maximum input power: 200 mW
- Audio frequency bandwidth: 15 - 25000 Hz
Cable
- Detachable: Yes
Wearing Style
- Over-ear: Yes
Cup Style
- Semi-open: Yes
AKG K361 Closed Back Studio Headphones
Sold Out $ 148.56
Over-ear, closed back, oval studio headphones.
K361s are precision-engineered to reproduce natural, balanced audio in exceptional detail, so you can make more confident decisions when you’re mixing and editing. They deliver deeper bass and higher highs than any other model in their class, with a stunning frequency response of 15 Hz to 28 kHz.
Unveil the Detail
Robust Design
Comfort Meets Style
Versatile Accessories
- Closed-back, oval over-ear design
- Superior isolation, improved low-frequency response, ergonomic fit
- Largest-in-class, 50mm transducers with pure OFC voice coils
- Superior sensitivity (114 dB SPL/V @ 1kHz) and impedance (32 ohms) for use with professional and consumer devices
- Best-in-class frequency response: 15 Hz to 28 kHz
- Calibrated headbands with slow-retention oval foam pads offer precise fit, superior comfort
- Fully foldable design for compact storage with 90 degree swivel earcups for single-ear monitoring
- Ultra-light weight: 219 grams (7.7 ounces)
- Sleek, stylish design
- Accessories include carrying pouch and versatile detachable cables:
- 3m (9.8') and 1.2m (2.5’) straight cables; 3.5mm (1/8”) to 6.5mm (1/4”) adapter
Upgrade to AKG and hear what you’ve been missing.
- Type: Over-ear
- Operating principle: Closed dynamic
- Frequency response: 15 Hz - 28 kHz
- Driver size: 50 mm
- Noise cancelling: No
- Primary application: Tracking, mixing, monitoring
- Built-in mic: No
- Cable type: Detachable
- Cable Length: 9.8' and 2.5'
- Connector: 3.5 mm with 1/4" adapter
AKG K99 Perception High Performance Headphones
$ 79.00 $ 119.00
The K99 Perception high-performance over-ear, semi-open headphones combine excellent sound quality and an astounding price/performance ratio. Their large, high-performance 40mm (1-7/12") speakers provide a natural, uncolored sound, ideal for project studios.
The K99 Perception features gimbal-suspended leatherette ear cups for easy cleaning. The self-adjusting, lightweight headband ensures a pleasant fit for long hours. The K99's come with a 3m (9-3/4ft) fixed, straight cable, including convertible jack plug.
TECHNICAL SPECIFICATION
| General |
|
||||||||||||||||
| Audio Interface |
|
||||||||||||||||
| Design |
|
||||||||||||||||
| Dimensions / Weight |
|
AKG P120 Studio Condenser Microphone
Sold Out $ 150.35
The P120 is a 2/3-inch diaphragm true condenser microphone that offers solidly built quality, outstanding performance and excellent value. The low-mass diaphragm delivers a clear sound with accurate sonic detail for vocals, speech and instrument recording in project studios and for home recording.
Studio vocal mic with instrument capability.
- Audio
- Frequency response: 20Hz to 20kHz
- Max SPL: 150 dB
- Sensitivity: 24 mV/Pa
- Pattern and type
- Capsule: Condenser
- Pattern: Cardioid
- Type: Mounted
- Applications
- Primary: Studio
- Secondary: Stage
- Other: Not applicable
- Physical
- L x W x (D): 6.5 x 2-1/10"
- Weight: 1lb. (455g)
- Other
- Case: Pouch
AKG P220 Condenser Microphone
$ 159.00 $ 266.90
The P220 is a large-diaphragm true condenser microphone offering a warm and clear sound for lead vocals, acoustic guitar and brass instruments. A switchable bass-cut filter and attenuation pad make it perfectly suited for use on loud sound sources with sound pressure levels up to 155dB SPL. The rugged and roadworthy design also makes the P220 a perfect choice for on-stage applications.
The P220 represents the most popular and successful microphone within the actual Project Studio Line. It comes complete with a spider-type shock mount in an aluminum carrying case.
General Specifications
Dimensions
Audio Output
Powering Interface
Application
Instrument
- 1 x P220 Microphone
- 1 x Spider Shock Mount
- 1 x Metal Carrying Case
AKG Perception 45 Instrumental Set Wireless System
$ 249.00 $ 379.00
The Perception Wireless Instrumental Set comprises an SR 45 receiver and PT 45 bodypack transmitter, the smallest and lightest transmitter in its class. It can be used with many AKG miniature microphones, and the battery compartment cover doubles as a convenient tool for setting input gain for the application at hand.
The system comes complete with a universal power supply with US/UK/EU adapter, MKG L cable with ¼" jack plug and mini XLR connector, and one AA size dry battery.
In combination with the C 519 ML (sold separately) also suitable for wind instruments.
SR 45 Stationary Receiver
The SR 45 Stationary Receiver delivers a diversity system, professional XLR and Jack outputs, and the SMPS solution. The audio level and squelch threshold are adjustable on the receiver. It is a stationary receiver for use with all transmitters of the Perception wireless system.
The SR 45 operates within a switching bandwidth of up to 30 MHz in the 500 to 560 MHz UHF carrier frequency range and offers up to 8 selectable carrier frequencies.
PT 45 bodypack transmitter
The PT 45 bodypack transmitter lets you use both dynamic microphones and condenser microphones operating on a supply voltage of approx. 4 V. Naturally you may also connect an electric guitar, electric bass or keytar.
The PT 45 operates within a switching bandwidth of up to 30 MHz in the 500 to 560 MHz UHF carrier frequency range and offers up to 8 selectable carrier frequencies.
Consumer Alert (for US users)
Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: The system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device.
Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC's wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones
A wireless system ideal for an exceptionally wide range of applications.
- 30 MHz selection bandwidth (depending on local frequency plans)
- 8 hours of operation with a single AA size battery
- Compatible with all AKG MicroMics
- Low battery indicator
- Smallest and lightest bodypack transmitter in its class
- Complete with MKG L cable for direct connection to electric guitar or bass
- IncludedPT 45 bodypack transmitterAA batteryMKG L cableSR 45 receiverSMPS switched mode power supplyGuarantee cardFrequency tableManual supplement sheet
Order a wireless system that faithfully reproduces the sound of your favorite instrument.
SPECIFICATIONS
Perception Wireless Instrumental Set
- SR 45 Stationary Receiver
- Carrier frequency range: 500 - 560 MHz
- Modulation: FM
- Audio bandwidth: 40 - 20,000 Hz
- T.H.D. at 1 kHz: typ. 0.8%
- Signal/noise ratio: typ. 105 dB(A)
- Squelch threshold: 100 to -70 dBm adjustable
- Audio outputs: Balanced XLR and unbalanced 1/4" (6.3 mm) jack: adjustable from mic to line level. Output level at rated deviation: 500 mV RMS
- Dimensions: 7.87" x 7.48" x 1.73", (200 x 190 x 44 mm)
- Net weight: 12.69 oz, (360 g)
- PT 45 bodypack transmitter
- Carrier frequency range: 500 - 560 MHz
- Modulation: FM
- Audio bandwidth: 40 - 20,000 Hz
- T.H.D. at 1 kHz: typ. 0.8%
- Signal/noise ratio: typ. 105 dB(A)
- RF output: 10 mW
- Power requirement: 1x 1.5 V AA size battery
- Battery life: 10 hours
- Dimensions: 2.36 " x 2.91" x 1.18", (60 x 74 x 30 mm)
- Net weight: 2.11 oz, (60 g)
Ampeg Heritage 50th Anniversary SVT Bass Amp Head
$ 2,999.99 $ 4,199.98
The Ampeg® SVT® is more than just a bass amp—it sparked a revolution. When it debuted in 1969, deafening walls of full-stack guitar amps were eating bass players alive. Knowing that big bass volume required big power, Ampeg designed the most sophisticated amp of its day: the 300-watt SVT. Finally, balance returned to the stage and with it a generation of iconic bass-forward music was born. That singular Ampeg spirt of innovation and ingenuity is alive and well in the Ampeg HeritageTM 50th Anniversary SVT bass amp. Designed to honor the unrivaled SVT legacy, the Heritage 50th Anniversary SVT distills the legendary amp’s most celebrated circuits into a single stage-ready head with a host of must-have modern technology and elegant vintage aesthetics. It truly is the SVT for the 21st century.
- The 1969 “Blue Line” and mid-1970s Magnavox-era circuits in one amp
- Handmade in the U.S.A. from durable top-shelf components
- Detailed, period-correct graphics and fonts
- Modern features include a newly enhanced XLR DI output, user biasing, speakOn® outputs, and spring-loaded side handles
- Specially sourced and matched Ampeg Super ValveTM 6550 tubes
- Not a reissue—the ultimate SVT for today
YOU ASKED FOR IT
From well-informed amateurs to elite professionals, no amp enjoys as passionate a fan base as the Ampeg SVT. For this new SVT, Ampeg surveyed its loyal customers to ensure that the design met and surpassed what’s on their wish lists. While each generation of the SVT has its faithful, Ampeg designed the Heritage 50th Anniversary SVT to satisfy even the most discerning SVT aficionados. It’s the SVT everyone has been asking for.
SPECIFICATIONS
- Preamp Tubes: 5 x 12AX7
- Driver Tubes: 1 x 12AX7, 2 x 12AU7
- Power Amp Tubes: Ampeg Super Valve (6 x 6550)
- Output Power Rating: 300W RMS minimum continuous @ <5% THD into @ 2 or 4
- Signal-to-Noise Ratio: (20 Hz – 20 kHz) 75 75 dB (20 Hz - 20 kHz)
- Maximum Gain: 78 dB @ 1 kHz –3 dB @ 20 Hz & 15 kHz
- Tone Controls
- Channel One: Voiced after original 1969 "Blue Line" SVT (jumpable)
- Channel Two: Voiced after mid 70's Magnavox era SVT (jumpable)
- Bass: +12/-12 dB @ 40 Hz
- Midrange: +10/-20 dB @ 220 Hz, 450 Hz, 800 Hz, 1.6 kHz, or 3 kHz
- Treble: +15/–20 dB @ 4 kHz
- Ultra Lo: +2 dB @ 40 Hz, -10 dB @ 500 Hz
- Ultra Hi: +9 dB @ 8 kHz
IDEAL CABINETS
- Heritage HSVT-810AV
- Classic SVT-810AV
- Classic SVT-212AV
- Classic SVT-112AV
Info
Shop
News & Updates
Sign up to get the latest on sales, new releases and more …
© 2024 Huber Breese Music. Powered by Shopify
